1 Reply Latest reply on Nov 25, 2018 10:44 PM by Brian Moore

    420rw print alote of white space at end ( roll paper )

    gregory belegrinos

      hello !

      i have made a simple android printing service  . i

      from android printing manager i convert the pdf  => image and then i print it with

      printer1.printImage(new ZebraImageAndroid( mergeMultiple(myBitmapList)), 0, 0,830,1200,false); // true false i have try it

      i have try all posible ways

      printer1.printImage(new ZebraImageAndroid( mergeMultiple(myBitmapList)), 0, 0);

      and set the label image  with

      SGD.SET("zpl.label_length", "1200", connection);

      but everytime its print ,i thing the height its have stored at device

       

      my "allcv" is

      bluetooth.
      bluetooth.encryption : on , Choices: on,off
      bluetooth.discoverable : on , Choices: on,off
      bluetooth.authentication : setpin , Choices: on,off,default,setpin
      bluetooth.friendly_name : ******// hidden 
      bluetooth.version : 2.1.14 
      bluetooth.date : 12/10/08 
      bluetooth.local_name : ******// hideen 
      bluetooth.address : ******* // hidden 
      bluetooth.bluetooth_pin : **** 
      bluetooth.short_address : ********// hidden 
      bluetooth.radio_version : 2.0 
      bluetooth.afh_mode : off , Choices: on,off
      bluetooth.afh_map : 7FFFFFFFFFFFFFFFFFFF 
      bluetooth.afh_map_curr : 7FFFFFFFFFFFFFFFFFFF 
      bluetooth.enable : on , Choices: on,off
      bluetooth.radio_auto_baud : 115 
      bluetooth.connected : No , Choices: Yes,No
      card.
      card.inserted : Not Inserted 
      card.cisproc
      card.mfgid
      card.cardid
      card.fncode
      card.idtext1
      card.idtext2
      card.idtext3
      card.idtext4
      card.fcrbase
      card.fcrlist
      card.defcfg
      card.cor
      card.defmacaddr
      card.mac_addr : //hidden 
      card.mac_raw : //hidden
      card.enable : off , Choices: on,off
      comm.
      comm.baud : 19200 , Choices: 19200,4800,9600,38400,57600,115200
      comm.data_bits : 8 , Choices: 8,7
      comm.parity : N , Choices: N,O,E
      comm.stop_bits : 1 , Choices: 1,2
      comm.dsr : on 
      head.
      head.latch : ok 
      ip.
      ip.dhcp.
      ip.dhcp.enable : off , Choices: on,off
      ip.dhcp.cid_type : 1 
      ip.dhcp.cid_prefix :  
      ip.dhcp.cid_value : 01:d1:06:30:1c:60 
      ip.dhcp.requests_per_session : 0 , Choices: 1-10
      ip.dhcp.request_timeout : 0 , Choices: 2-30
      ip.dhcp.session_interval : 0 , Choices: 0-60
      ip.dhcp.lease.
      ip.dhcp.lease.length : 0 
      ip.dhcp.lease.time_left : 0 
      ip.dhcp.lease.server : 0.0.0.0 
      ip.dhcp.lease.last_attempt : 0 
      ip.dhcp.cache_ip : off , Choices: on,off
      ip.dhcp.vendor_class_id :  
      ip.dhcp.user_class_id :  
      ip.dhcp.option12 : on 
      ip.dhcp.option12_format :  
      ip.dhcp.option12_value : Rw4201093 
      ip.ftp.
      ip.ftp.enable : off , Choices: on,off
      ip.ftp.execute_file : off , Choices: on,off
      ip.lpd.
      ip.lpd.enable : off , Choices: on,off
      ip.tcp.
      ip.tcp.enable : off , Choices: on,off
      ip.udp.
      ip.udp.enable : off , Choices: on,off
      ip.http.
      ip.http.enable : off , Choices: on,off
      ip.smtp.
      ip.smtp.enable : off , Choices: on,off
      ip.smtp.server_addr :  
      ip.pop3.
      ip.pop3.enable : off , Choices: on,off
      ip.pop3.print_headers : off , Choices: on,off
      ip.pop3.verbose_headers : off , Choices: on,off
      ip.pop3.print_body : off , Choices: on,off
      ip.pop3.save_attachments : off , Choices: on,off
      ip.pop3.poll : 0 
      ip.pop3.username :  
      ip.pop3.password :  
      ip.pop3.server_addr :  
      ip.pop3.print_attachments : off , Choices: on,off
      ip.snmp.
      ip.snmp.enable : off , Choices: on,off
      ip.snmp.get_community_name :  
      ip.snmp.set_community_name :  
      ip.snmp.create_mib
      ip.telnet.
      ip.telnet.enable : off , Choices: on,off
      ip.telnet.disconnect
      ip.addr : 0.0.0.0 
      ip.netmask : 0.0.0.0 
      ip.gateway : 0.0.0.0 
      ip.port : 0 
      ip.remote :  
      ip.ping_remote
      ip.netstat : TCP/IP is not initialized. 
      ip.remote_port : 0 
      ip.remote_autoconnect : off , Choices: on,off
      ip.bootp.
      ip.bootp.enable : off , Choices: on,off
      ip.mirror.
      ip.mirror.auto : off , Choices: on,off
      ip.mirror.username : user 
      ip.mirror.password : ******** 
      ip.mirror.server : 127.0.0.1 
      ip.mirror.path : Zebra 
      ip.mirror.freq : 0 
      ip.mirror.fetch
      ip.mirror.version : Sep 29 2008 12:14:56
      
      ip.mirror.freq_hours : 0 
      ip.mirror.error_retry : 0 
      ip.mirror.feedback.
      ip.mirror.feedback.auto : off , Choices: on,off
      ip.mirror.feedback.path : Zebra/feedback 
      ip.mirror.feedback.freq : 0 
      ip.mirror.feedback.size : 4000 , Choices: size: bytes (4K-32K)
      ip.mirror.success : No 
      ip.mirror.success_time : 0 
      ip.mirror.last_time : 0 
      ip.mirror.last_error :  
      ip.mirror.file_failsafe : on , Choices: on,off
      ip.mirror.mode : ftp , Choices: ftp,sftp
      ip.vpn.
      ip.vpn.username : user 
      ip.vpn.password : ******** 
      ip.vpn.domain : mydomain 
      ip.vpn.mode : off 
      ip.vpn.addr : 0.0.0.0 
      ip.vpn.version : May 12 2008 11:46:53
      
      ip.vpn.status :  
      ip.ping_len : 10 
      ip.dns.
      ip.dns.domain : 0 …H0 
      ip.dns.servers : 0 …H0 
      ip.discovery.
      ip.discovery.enable : off , Choices: on,off
      ip.discovery.port : 4201 
      ip.roam_packet : on , Choices: on,off
      ip.ssh.
      ip.ssh.server.
      ip.ssh.server.enable : off , Choices: on,off
      ip.ipsec.
      ip.ipsec.enable : off 
      ip.ipsec.rules : TCP/IP is not initialized. 
      label.
      label.x_move : 0 , Choices: inc,dec,nnn
      label.y_move : 0 , Choices: inc,dec,nnn
      label.crc :  
      label.calculate_crc
      label.noprint : off , Choices: on, off, p_on, p_off
      motor.
      motor.direction : forward 
      media.
      media.status : ok 
      media.sense_mode : bar , Choices: gap,bar
      media.tof : 0 , Choices: up,down,value
      media.type : journal , Choices: journal,label
      media.width_sense.
      media.width_sense.enable : on , Choices: on,off
      media.width_sense.in_mm : 104.0 
      media.width_sense.in_cm :  10.40 
      media.width_sense.in_dots : 832 
      media.width_sense.in_inches :  4.098 
      sensor.
      sensor.ribbon : no ribbon 
      sensor.paper_supply : ok 
      sensor.peeler : clear 
      srf.
      wlan.
      wlan.operating_mode, Choices: ad hoc,infrastructure
      wlan.essid
      wlan.current_essid
      wlan.station_name
      wlan.tx_rate, Choices: 1,2,5.5,11,all
      wlan.current_tx_rate
      wlan.encryption_mode, Choices: off,40-bit,128-bit
      wlan.associated, Choices: yes,no
      wlan.encryption_index, Choices: 1,2,3,4
      wlan.encryption_key1
      wlan.encryption_key2
      wlan.encryption_key3
      wlan.encryption_key4
      wlan.leap_mode, Choices: off,on
      wlan.leap_username
      wlan.leap_password
      wlan.power_save, Choices: off,1,2,3,4,best
      wlan.test.
      wlan.kerberos.
      wlan.kerberos.mode, Choices: off,on
      wlan.kerberos.username
      wlan.kerberos.password
      wlan.kerberos.realm
      wlan.kerberos.kdc
      wlan.auth_type, Choices: open,shared
      wlan.preamble, Choices: long,short
      wlan.bssid
      wlan.tx_power, Choices: 1,5,20,30,50,100
      wlan.firmware_version
      wlan.signal_strength
      wlan.scrambler, Choices: off,on
      wlan.bias_supp, Choices: off,on
      wlan.current_freq
      wlan.current_hop_index
      wlan.international_mode, Choices: off,on,auto
      wlan.roam.
      wlan.roam.signal
      wlan.roam.interval
      wlan.roam.monitor
      wlan.roam.interchannel_delay
      wlan.roam.max_chan_scan_time
      wlan.khz
      wlan.channel
      wlan.wpa.
      wlan.wpa.enable : off , Choices: off,on
      wlan.wpa.authentication, Choices: psk,leap,eap-tls,peap,ttls,fast
      wlan.wpa.psk
      wlan.wpa.mixedmode : off , Choices: off,on
      wlan.wpa.wpa_version :  
      wlan.wpa.groupkey_ciphersuite :  
      wlan.wpa.pairwise_ciphersuite :  
      wlan.8021x.
      wlan.8021x.enable : off , Choices: off,on,wpa
      wlan.8021x.authentication, Choices: psk,leap,eap-tls,peap,ttls,fast
      wlan.8021x.peap.
      wlan.8021x.peap.peap_username
      wlan.8021x.peap.peap_password
      wlan.8021x.peap.privkey_password
      wlan.8021x.eap.
      wlan.8021x.eap.username
      wlan.8021x.eap.password
      wlan.8021x.eap.privkey_password
      wlan.adhocchannel, Choices: 1,2,3,4,5,6,7,8,9,10,11,12,13,14
      wlan.adhocautomode, Choices: off, on
      wlan.enable : off 
      wlan.encryption_optional, Choices: yes,no
      wlan.adhoc_last_channel
      wlan.secure_ssid : off 
      wlan.ip.
      wlan.ip.addr : 0.0.0.0 
      wlan.ip.netmask : 0.0.0.0 
      wlan.keep_alive.
      wlan.keep_alive.enable : off , Choices: off,on
      wlan.keep_alive.timeout : 0 
      display.
      display.contrast :  4 
      display.text :    Zebra RW 420     Baud Rate:19200     Batteryή²²²²ΝΓ(ok)  Latch: ok     Menu   
      display.backlight : on , Choices: on,off
      display.icon_contrast : 0 , Choices: up,down,0-3
      display.print
      display.flip_display : off , Choices: normal,auto,reversed
      display.backlight_on_time : 10 , Choices: 1-65535
      display.counter, Choices: off,0-19999,getvar
      memory.
      memory.flash_size : 8388607 Bytes 
      memory.ram_size : 16777215 Bytes 
      memory.flash_free : 3980000 Bytes Free 
      memory.ram_free : 10078707 Bytes Free 
      memory.clear
      power.
      power.voltage : 7.84 
      power.percent_full :  80% Full 
      power.status : ok 
      power.low_battery_warning : 7.10(182) 
      power.low_battery_shutdown : 6.79(174) 
      power.low_battery_timeout :   60 Seconds 
      power.inactivity_timeout :    0 Seconds 
      power.dtr_power_off : off , Choices: on,off
      power.shutdown
      power.ascii_graph : ή²²²²ΝΓ 
      power.low_battery_warning_raw : 182 
      power.power_on_cycles : 1809 
      power.percent_raw :  80 
      power.design_voltage
      power.design_capacity
      power.manufacture_date
      power.relative_state_of_charge
      power.serial_number
      power.temperature
      power.cycle_count
      power.manufacturer_data
      power.full_charge_capacity
      power.health
      power.date_first_used
      power.charge_start
      power.charge_stop
      power.charge_reset
      file.
      file.dir :   Directory
         ZPL_CFG .CFG        84
         CONFIG  .SYS        55
         FF3     .BAT       116
         INDEX   .WML      4532
         OILCHANG.ZPL       708
         3980000 Bytes Free
      
      file.type
      file.delete
      file.print
      file.run
      file.rename
      file.append
      file.failsafe : on , Choices: on, off
      test.
      test.print_diags
      test.report_diags
      test.feed
      odometer.
      odometer.user_label_count : 18480 , Choices: 0-65535
      odometer.total_label_count :       308 
      odometer.total_print_length :   1643366 mm 
      odometer.media_marker_count :    59 , Choices: 0-65535
      odometer.latch_open_count :   201 , Choices: 0-65535
      odometer.label_dot_length :     0 
      odometer.rfid.
      appl.
      appl.date : 02/02/09 
      appl.name : SHSCG11x20           
      appl.version : 9011 
      appl.ps.
      appl.in : RAM 
      device.
      device.reset
      device.restore_defaults, Choices: wlan,ip,display,power,bluetooth
      device.card.
      device.card.description : Bluetooth 
      device.card.name : Bluetooth 
      device.card.id : 0x77 
      device.bridge.
      device.bridge.enable : off , Choices: on,off,interim_on
      device.friendly_name : Rw420
      device.company_name : Zebra 
      device.product_name : RW 420 
      device.status : ready 
      device.pld.
      device.pld.model : 0 
      device.pld.rev : 0 
      device.ms_tick_count : 17920 
      device.jobs_print : 0 
      device.label_counter : 0 
      device.languages : zpl , Choices: EPL, ZPL, epl_zpl, line_print, aplm
      device.cph_enable : off , Choices: on,off
      device.cph_interval :   300 , Choices: 0-65535
      device.macro_get
      device.user_p1 : ? 
      device.user_p2 : ? 
      device.two_key_wait : 2 , Choices: 0-15
      device.uptime : 12 
      device.volume : high , Choices: high, medium, low
      device.local_menu_mode
      device.ff_disable : off , Choices: on, off
      device.ftn_disable : off , Choices: on, off
      device.h8_comp : 0 
      input.
      

       

      any suggestions please ?